One metre of copper core HT lead, this is superior to the more commonly available carbon core lead

Sold by the metre, one metre is enough for two leads on most models with coils under the fuel tank. For models with coils under the side panel you will need two metres. See ELA14715 and ELA14714 for plug caps. See ELA00001 for crimp on HT lead connector

Dimensions:
100cm

Set of ignition points (made up of two boxes of contacts)

 19709620 GU19709620 19 70 96 20
 1970 9620 1970.9620 19.70.96.20

Black clutch lever

See CLA17605 for this lever in aluminium finish. Can also be inverted for use as a brake lever on V50 II and V35 I with cable operated brake

14605750-z 14605750 GU14605750 14 60 57 50
 1460 5750 1460.5750 14.60.57.50

Dimensions:
5.8mm internal diameter mounting hole

Pivot bolt and special nut for Brembo PS 13 and PS 16 master cylinders, also used for some hydraulic clutch lever pivot bolts

Not for early Cali 1100s fitted with solid brake lever pivot pins. Brembo ref. 110279850

 10279850 GU10279850 10 27 98 50
 1027 9850 1027.9850 10.27.98.50

Dimensions:
12mm pivot OD

1 litre of EP75/90 synthetic gear oil for modern gearboxes

A premium OEM gear oil formulated using the latest technology for gearbox applications requiring a 75w90 viscosity. XF Premium gear oil provides enhanced low temperature flow when cold starting, instantly protecting the vital components of the gearbox from the very start of every journey.

XF Premium gearbox oil maximises viscosity stability at high temperatures. This reduces gearbox wear giving superior component protection including gear teeth, shafts and bearings.

Delivers outstanding lubrication and instant protection under hot and cold temperatures. This is an oil specially formulated for and approved by Moto Guzzi. It protects and lubricates over a wide temperature range and under extreme conditions. Also approved by Piaggio, Aprilia, Derbi, Gilera and Vespa. Exceeds API GL-5. Used as gearbox oil in 6 speed V7 and V9 models
Quantities required:

• V9, V7 II and V7 III 6 speed gearbox 0.5l

Dimensions:
1 litre

Brembo brake caliper rebuild kit for one P2 F08 (P8) caliper, contains 2 pairs of seals, O ring and 2 M10 bolts

This seal kit is for F08 calipers fitted to front of all these models. Also used on some Triumph Bonnevilles, MZs, Ducati 600 Pantah, 500 Pantah, 500 Sport Desmo, 500 GTV, 650 SL, 750 F1, 750 F1B, 750 Paso, 750 Sport, 900 MHR, 900 SS, 900 S2, 906 Paso, 100 R1, 100 S2 Desmo, Laverda Jota 1000 and Laverda 1200 Anniversary. Brembo ref. 120274110

See BRA10310 for less expensive replica kit

 14659000 GU14659000 14 65 90 00
 1465 9000 1465.9000 14.65.90.00

Also fits Benelli 354, Benelli Sei, Ducati 250/350/450 Desmo (-1976), Ducati Pantah, Ducati F1, Ducati 750 Paso (1987-1990), Ducati 750 Sport (1988-1990), Ducati 860 GT/GTS, Ducati 900 GTS, Ducati Hailwood Rep, Ducati 900 Darmah (1977-1978), Ducati 906 Paso (1988-1989), Ducati 1000 R1 Hailwood Ref., Hesketh, Horex HRD 600, Horex 500/600 Columbus, Laverda 750 SF2, Laverda 750 SFC, Laverda 750 SF3, Laverda 1000 3C (1974-1978), Laverda 1000 3CL (1976-1981), Laverda 1000 RGS/RGA, Laverda 1000 SFC, Laverda 1200 (1978-1979), Laverda 1200 TS/Mirage (1981), MZ ETZ 125/150/250/300 (1985-1992), Norton Classic (1989), Norton Interpol (1989), Triumph T140 (1985-1988 Brembo)

Brembo rebuild kit for Brembo F05 (P5) calipers with 32mm pistons. Contains 2 bolts, all seals and brake grease

This caliper also known as P2 F05N, P32B and P32F.
This seal kit also known as Brembo ref. 120279910, also used on Benelli 504 Sport, 650 Al'Azzura, Ducati 500s, Laverda 500 Montjuich and Zeta (front) and Bimota DB1 and YB4 (rear).

Not suitable for P32 rear calipers fitted to 750T and Nevada 750 (1991-2001) - see BRA01723 for this model. Will not fit pistons on Grimeca F05 calipers.

 39659000 GU39659000 39 65 90 00
 3965 9000 3965.9000 39.65.90.00

Also fits Benelli 504 Sport, Benelli 250 TS, Ducati Pantah 500SL, 650 Al'Azzura, Ducati 500s, Laverda 500 Montjuich and Zeta (front) and Bimota DB1 and YB4

Oil pressure sender, M12 thread, male bullet connector

This oil pressure sensor supercedes Guzzi no. 12768700. Some small twins also require adapter 19055800 (or ELA19720 can be fitted in place of this switch). Check which type your small twin uses before replacing.

See ENA12640 for replacement crush washer if required

 17768750 GU17768750 17 76 87 50
 1776 8750 1776.8750 17.76.87.50

Dimensions:
M12 thread, 46mm x 21mm bolt flats

Sebac fork damper, standard damping rate

Also known as Guzzi ref. 18526460. See OIA01001 for ATF (used in place of fork oil)

14526455-z 14526455 GU14526455 14 52 64 55
 1452 6455 1452.6455 14.52.64.55

Also fits Benelli Sei 900

Brembo brake master cylinder overhaul kit for overhauling foot operated PS 15 master cylinders on linked systems. Includes all seals and brake grease.

This seal kit replaces Guzzi part numbers 17659350, 66139790. Brembo ref. 110273920. This repair kit also used on some Cagiva 650 Elefant models and Benelli Sei. Some Nevada 750 models use BRA14701, check your rear master cylinder before ordering. See this link for help with fitting this kit. Supercedes front kit BRA11043
Note that this kit is only for PS15 models where the piston is retained by a ring, if your master cylinder has a circlip retaining the piston then you have a PS 16 and you will need kit BRA37232

 10273920 GU10273920 10 27 39 20
 1027 3920 1027.3920 10.27.39.20

Also fits Benelli Sei, Cagiva Elefant, Ducati 600 SL Pantah, Ducati 750/900 SS, Ducati 860/900 GTS, Ducati 900 Darmah, Ducati 900 MHR, Ducati 1000 MHR, Ducati 750 Sport (1972-1974), Laverda Jota

Dimensions:
Solid piston 15.84mm OD x 65mm