Dimensions:
16mm threaded section, 8mm fuel pipe spigot
Manual right hand petrol tap with nut and filter. On, Off and Reserve settings.
Point on lever faces back in off position. Can be used to replace electronic fuel solenoid valve 37105305
More than 5 in stock
17105460-z 17105460 GU17105460 17 10 54 60
1710 5460 1710.5460 17.10.54.60
£12.50
INC VAT
£10.42 EX VAT
Sebac fork damper, standard damping rate
See OIA01001 for ATF (used in place of fork oil)
3 in stock
14526407-z 14526407 GU14526407 14 52 64 07
1452 6407 1452.6407 14.52.64.07
£32.00
INC VAT
£26.67 EX VAT
Dimensions:
588mm
Complete (rev counter) tacho cable
We advise you to measure your existing cable before ordering in case you have a non standard set up.
More than 5 in stock
19768100-z 19768100 GU19768100 19 76 81 00
1976 8100 1976.8100 19.76.81.00
£12.50
INC VAT
£10.42 EX VAT
Carb gasket kit / rebuild kit for Dellorto VHB29, VHB30, VHB24 and VHB26 carbs
Carb overhaul kit, fuel filter FUA60888 and float bowl seal FUA90001 available separately to this seal kit. As this kit is intended for several different carbs you may have gaskets or O rings remaining after rebuilding. More information on rebuilding your VHB carb can be found here.
More than 5 in stock
17939950 GU17939950 17 93 99 50
1793 9950 1793.9950 17.93.99.50
£12.50
INC VAT
£10.42 EX VAT
Carb gasket kit / rebuild kit for Dellorto VHB29, VHB30, VHB24 and VHB26 carbs
Carb overhaul kit, fuel filter FUA60888 and float bowl seal FUA90001 available separately to this seal kit. As this kit is intended for several different carbs you may have gaskets or O rings remaining after rebuilding. More information on rebuilding your VHB carb can be found here.
More than 5 in stock
17939950 GU17939950 17 93 99 50
1793 9950 1793.9950 17.93.99.50
£12.50
INC VAT
£10.42 EX VAT
Dellorto carb gasket kit / rebuild kit for PHF30, contains necessary rubber seals and gaskets to recondition a carburettor
Carb overhaul kit, fuel filter FUA60888 and float bowl seal FUA90001 available separately to this seal kit
2 in stock
28939911 GU28939911 28 93 99 11
2893 9911 2893.9911 28.93.99.11
£21.00
INC VAT
£17.50 EX VAT
Dimensions:
105mm x 45mm diameter overall
UFI 25 46 500 cartridge oil filter. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick
For post 1989 V35, V50 and V65 models use SIA27300 .
NB Packaging may vary. For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer)
More than 5 in stock
19153000 GU19153000 19 15 30 00
1915 3000 1915.3000 19.15.30.00
£8.50
INC VAT
£7.08 EX VAT
Dimensions:
For 16mm threaded spigot
Cartridge oil filter UFI 23 149 00
Fits Daytona 1000 models where filter screws into base of sump. This is an 8 sided UFI filter.
Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump.
You may also require SIA10070 which is the crush washer for the drain plug and ENA14036 (sump gasket).
Please note that Daytona RS and T5 Polizia use filter SIA15300
More than 5 in stock
14153000 GU14153000 14 15 30 00
1415 3000 1415.3000 14.15.30.00
£10.50
INC VAT
£8.75 EX VAT
Sealed swing arm taper needle roller bearing
Bearing is sealed on one side (not pictured). See FRA92225 for related dust seal
2 in stock
92249224 GU92249224 92 24 92 24
9224 9224 9224.9224 92.24.92.24
£42.00
INC VAT
£35.00 EX VAT
Sealed swing arm taper needle roller bearing
Bearing is sealed on one side (not pictured). See FRA92225 for related dust seal
2 in stock
92249224 GU92249224 92 24 92 24
9224 9224 9224.9224 92.24.92.24
£42.00
INC VAT
£35.00 EX VAT
Secure online shopping 
