Round 12v two pin flasher relay

See FRA17720 for rubber mount, item may look different to this please take into consideration before ordering.

 17750520 GU17750520 17 75 05 20
 1775 0520 1775.0520 17.75.05.20

Dimensions:
32mm diameter

Quick release coupling for fuel line, enables easier tank removal as QR connector can be located in a convenient location.

We recommend fitting this now before you snap the coupling on your fuel pump

Dimensions:
for 8mm ID pipe

Round 12v two pin flasher relay

See FRA17720 for rubber mount, item may look different to this please take into consideration before ordering.

 17750520 GU17750520 17 75 05 20
 1775 0520 1775.0520 17.75.05.20

Dimensions:
32mm diameter

12 volt ignition coil for models equipped with points, Bosch or Motoplat ignition systems, includes HT lead. Terminal layout is different to original coils- see photos.

Not for Digiplex models. Also known as Guzzi ref. 19716500, 19716520

 31716560 GU31716560 31 71 65 60
 3171 6560 3171.6560 31.71.65.60

Dimensions:
80mm mounting spacing

M6 bleed nipple for Brembo F05 and twin bleed P2 F08 & F09 calipers. Manufactured specially for Gutsibits in corrosion resistant grade 5 titanium as a replica of the original Brembo M6 bleed nipple

Use M10 bleed screw SSA36794 for single bleed (later) P8 calipers. Ducati ref. 079539787
See BRA36794 for rubber cap

Also fits Benelli 250 TS, Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 F1/Laguna Sec, KTM 250XC, KTM 250SX, KTM 250EXC,

Dimensions:
6mm threaded shank, 8mm across flats

Titanium rocker feed and breather M8 banjo bolt

Made specially for Gutsibits in corrosion resistant grade 5 titanium. Use with SIA12200 crush washer

 95990037 GU95990037 95 99 00 37
 9599 0037 9599.0037 95.99.00.37

Dimensions:
M8 x 1.25

Marelli air temperature sensor

Supplied with screws. Two required per engine

 30729330 GU30729330 30 72 93 30
 3072 9330 3072.9330 30.72.93.30

JMP cartridge oil filter for 1989 on small block engines. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick

For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer). Some 750 XPA models use SIA19530, we advise you to check your old filter before ordering. Also known as Guzzi ref. 2A000633

 27153085 GU27153085 27 15 30 85
 2715 3085 2715.3085 27.15.30.85

Dimensions:
120mm x 45mm diameter overall

UFI 25 531 00 cartridge oil filter for 1989 on small block engines. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick, If this item is out of stock we do stock a like for like replacement, which is this item SIA27301 .

For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer). Some 750 XPA models use SIA19530, we advise you to check your old filter before ordering. Also known as Guzzi ref. 2A000633

 27153085 GU27153085 27 15 30 85
 2715 3085 2715.3085 27.15.30.85

Dimensions:
120mm x 45mm diameter overall

Special tool for tightening and untightening the dipstick on small twins. The dipstick can be awkward to undo on these models but this tool makes it simple and quick. No more struggling to grip it or resorting to pliers, just use our tool.

Oil filler tool manufactured from PETG filament these are fully recyclable but as strong as ABS. Dipstick spanner 3D printed in the UK

 14927001 GU14927001 14 92 70 01
 1492 7001 1492.7001 14.92.70.01