Gearbox input seal and output shaft oil seal on big twins, fork seal on Nuovo Falcone. Used as crownwheel shaft oil seal on small twins. Output seal only on 4 speed gearboxes
Supercedes Guzzi ref. 90403547. Used as crownwheel carrier seal on small twins Also known as Guzzi ref. 90403549
More than 5 in stock
90403548 GU90403548 90 40 35 48
9040 3548 9040.3548 90.40.35.48
£18.50
INC VAT
£15.42 EX VAT
Rear crankcase oil seal or rear main oil seal.
Fits Nevada 750 up to engine LT017877 and Nevada 350 to engine PC053625. Also known as Guzzi ref. 90405368. We recommend replacing the rear crank oil seal when replacing the clutch
More than 5 in stock
90405367-z 90405367 GU90405367 90 40 53 67
9040 5367 9040.5367 90.40.53.67
£14.00
INC VAT
£11.67 EX VAT
Swing arm taper roller bearing
2 races required per bike, supercedes unsealed bearing Guzzi ref. 92249217 and 92249216. See TRA90434 for oil seals
More than 5 in stock
92249213 GU92249213 92 24 92 13
9224 9213 9224.9213 92.24.92.13
£18.80
INC VAT
£15.67 EX VAT
Needle roller bearing used in lower suspension linkage for rear shock absorber. 7 bearings required per bike
See SUA81068 for bearing oil seal
More than 5 in stock
AP8110066
£6.60
INC VAT
£5.50 EX VAT
Small and large 90° rubber pipes for connecting crankcase breather spigots to breather box
Guzzi part ref. 17154950 & 17154850
5 in stock
17154850-z 17154850 GU17154850 17 15 48 50
1715 4850 1715.4850 17.15.48.50
£9.90
INC VAT
£8.25 EX VAT
Rubber brake cable sleeve for lower end of cable
3 in stock
12626300-z 12626300 GU12626300 12 62 63 00
1262 6300 1262.6300 12.62.63.00
£8.30
INC VAT
£6.92 EX VAT
Fork seal
3 in stock
30532861 GU30532861 30 53 28 61
3053 2861 3053.2861 30.53.28.61
£8.90
INC VAT
£7.42 EX VAT
60/55W H4 P43T headlamp / headlight bulb
This is the more modern H4 bulb with three tabs . Also known as Guzzi ref. 292723
3 in stock
93450232 GU93450232 93 45 02 32
9345 0232 9345.0232 93.45.02.32
£6.10
INC VAT
£5.08 EX VAT
Stainless steel braided hose oil lines for heads on square barrel models. See ENA14662 if you also need threaded link to cylinder head
Always replace crush washers (SIA12200 x 2 and SIA10900 x 2) when replacing oil lines, you may also require our banjo bolt ENA95990. Also known as Guzzi ref. 01153600 and 01153602
4 in stock
14153660 GU14153660 14 15 36 60
1415 3660 1415.3660 14.15.36.60
£53.00
INC VAT
£44.17 EX VAT
Swing arm seal for CARC models
Swingarm dust seal, locates in recess behind bearing
2 in stock
05547930 GU05547930 05 54 79 30
0554 7930 0554.7930 05.54.79.30
£8.28
INC VAT
£6.90 EX VAT