1 litre of EP75/90 synthetic gear oil for modern gearboxes

A premium OEM gear oil formulated using the latest technology for gearbox applications requiring a 75w90 viscosity. XF Premium gear oil provides enhanced low temperature flow when cold starting, instantly protecting the vital components of the gearbox from the very start of every journey.

XF Premium gearbox oil maximises viscosity stability at high temperatures. This reduces gearbox wear giving superior component protection including gear teeth, shafts and bearings.

Delivers outstanding lubrication and instant protection under hot and cold temperatures. This is an oil specially formulated for and approved by Moto Guzzi. It protects and lubricates over a wide temperature range and under extreme conditions. Also approved by Piaggio, Aprilia, Derbi, Gilera and Vespa. Exceeds API GL-5. Used as gearbox oil in 6 speed V7 and V9 models
Quantities required:

• V9, V7 II and V7 III 6 speed gearbox 0.5l

Dimensions:
1 litre

Black rubber UJ gaiter / boot, clips available separately - see SSA64990 and TRA12544

 18548000 GU18548000 18 54 80 00
 1854 8000 1854.8000 18.54.80.00

Dimensions:
54mm internal diameter (small end), 70mm diameter (big end) x 40mm

Gearbox input seal

Also known as Guzzi ref. 90402737

 90402736 GU90402736 90 40 27 36
 9040 2736 9040.2736 90.40.27.36

Dimensions:
37mm OD

Brembo brake master cylinder overhaul kit for handlebar, undertank (cable operated) mounted, handlebar mounted and rear PS 12 master cylinders. Contains seals, brake grease, spring and piston. PS12 handlebar master cylinder fitted to early 850 and 1000 models. PS12 rear master cylinder fitted to Nevada 750

This seal kit is also known as 082039797. NB repair kit instructions refer to rear master cylinder. To fit this to a PS12 handlebar mounted cylinder you will need to punch the old piston out using a thin drift through the hole at the banjo bolt end of the master cylinder. Carefully note the order of the ring and washer as the piston comes out and replace with components from kit. Brembo no. 110279720. See this link for help with fitting this kit

 17659352 GU17659352 17 65 93 52
 1765 9352 1765.9352 17.65.93.52

Also fits Ducati 500 SL Pantah, Ducati 350/500 Twin GTV, Ducati 350/500 SL Pantah, Benelli 500 Quattro, Benelli 504 Sport, Benelli 250 2C, Benelli 900 Sei, Laverda Montjuic, Harris F1

Dimensions:
Solid piston 12.7mm OD x 65mm

Rebuild kit for Brembo PS 13 handlebar mounted brake and clutch master cylinders, includes all seals, return spring and brake grease. Piston is hollow

This seal kit is for Cali 1100 master cylinders with a hollow pivot pin, does not fit early models with a solid pivot pin. For Cali EV models this only fits master cylinders with a pair of screws in the middle of the cap, it does not fit the later master cylinder which has diagonally opposed screws. Also know as Guzzi ref. 28659378, 000043851, 30659330. NB Included instructions may refer to rear master cylinder applications rather than front. Brembo ref. 110436250

Also fits Cagiva Elefant E750, Ducati 748

Dimensions:
Hollow piston 13mm OD x 38mm

Dellorto needle valve kit comprising of valve and felt washer

200 needle valve for VHB24, VHB26 and PHBH carbs

 19934600 GU19934600 19 93 46 00
 1993 4600 1993.4600 19.93.46.00

Set of ignition points (made up of two boxes of contacts)

 19709620 GU19709620 19 70 96 20
 1970 9620 1970.9620 19.70.96.20

Air filter, flat paper cartridge type for models with single throttle body

See SIA10434 for a reusable performance air filter

AP8104924

Dimensions:
120mm x 80mm x 53mm

Pair of Brembo 07BB0106 carbon ceramic brake pads with wear indicators for Brembo F05 (P5) and Grimeca calipers

For rear only on Daytona, 1100 Sport, Centauro and V11 Sport. Fronts only on Strada 750 (Brembo equipped). Fits Nevada up until frame no. LK112433 Fits V50 ALL front and rear

27654610-z 27654610 GU27654610 27 65 46 10
 2765 4610 2765.4610 27.65.46.10

Also fits Benelli 125 2C Fronts, Benelli 504 Sport Fronts (1976), Benelli 654 Fronts (1983), Bimota YB7 Rear (1989), Ducati 620 i.e Rear (2001), Ducati Monster 900 i.e. Rear (2002), Ducati Monster 1000 Rear (2003), Ducati Monster 1000 S Rear (2004), Ducati Monster S4 Rear (2001), Moto Morini Dart 350 Rear (1987), Moto Morini 350 Kanguro Rear (1987), Moto Morini Excaliber 350/501 Rear (1993-)

Dimensions:
40mm x 57mm x 7mm overall

Input shaft oil seal for gearbox

 90403245 GU90403245 90 40 32 45
 9040 3245 9040.3245 90.40.32.45

Dimensions:
45mm OD