UFI 31 504 00 fuel filter, threaded connections, includes copper washers. See FUA29107 for alternative filter from Mahle

Replace every 6000 miles. Replaces Guzzi refs. 29106060 and 29999660. Only for series 1 Daytona 1000. Will not fit early Cali 3s which have filters with two 14mm threads.

 29106061 GU29106061 29 10 60 61
 2910 6061 2910.6061 29.10.60.61

Dimensions:
approx 140mm x 60mm diameter. M14 + M12 threads

UFI 27 77 900 conical air filter

See FUA90552 for air filter housing O ring

 17113651 GU17113651 17 11 36 51
 1711 3651 1711.3651 17.11.36.51

Dimensions:
approx 195mm x 75mm diameter at wide end

Pinion oil seal for rear drive box on small twins and rear wheel bearing oil seal for 850T

 90403247 GU90403247 90 40 32 47
 9040 3247 9040.3247 90.40.32.47

Dimensions:
47mm OD

High pressure black fuel line / fuel line

Also known as Guzzi ref. 008239520800, 00823941078, GU00823952080. This high pressure fuel hose is rated to 10 Bar. Also see FUA80000 of a Y shaped connector or FUA80001 for a T shaped fuel line connector. R7 spec. E5 and E10 ethanol resistant

823952080

Dimensions:
7.5mm ID x 13.5mm OD x 1m length

12 volt ignition coil for models equipped with points, Bosch or Motoplat ignition systems, includes HT lead. Terminal layout is different to original coils- see photos.

Not for Digiplex models. Also known as Guzzi ref. 19716500, 19716520

 31716560 GU31716560 31 71 65 60
 3171 6560 3171.6560 31.71.65.60

Dimensions:
80mm mounting spacing

Inlet manifold rubber. Fits between exhaust manifold on cylinder head and carb

Use clip SSA25950

19114320-z 19114320 GU19114320 19 11 43 20
 1911 4320 1911.4320 19.11.43.20

Dimensions:
33mm ID x 39mm length

Round 12v two pin flasher relay

See FRA17720 for rubber mount, item may look different to this please take into consideration before ordering.

 17750520 GU17750520 17 75 05 20
 1775 0520 1775.0520 17.75.05.20

Dimensions:
32mm diameter

Inlet rubber with HT lead guide. This part will only fit the PHM40 carbs with 43.5mm inlet stubs, we recommend measuring your carbs before ordering

Fits between exhaust manifold on cylinder head and carb. Use clip SSA45970

28114360-z 28114360 GU28114360 28 11 43 60
 2811 4360 2811.4360 28.11.43.60

Dimensions:
43.5mm ID x 38mm length

Inlet manifold rubber. Fits between exhaust manifold on cylinder head and carb

Also known as Guzzi ref. 19114360. 31114060. Use clip SSA32957

31114383-z 31114383 GU31114383 31 11 43 83
 3111 4383 3111.4383 31.11.43.83

Dimensions:
35mm internal diameter x 50mm outer diameter x 36mm

Air filter, flat paper cartridge type for models with single throttle body

See SIA10434 for a reusable performance air filter

AP8104924

Dimensions:
120mm x 80mm x 53mm