Pair of engine crash bars for V7 models (including single throttle body models) finished in bright chrome. The heads and rocker covers are vulnerable on these bikes and can be badly damaged by even a minor accident, replacement cost can be more than £1000 so protect your bike with these bars.

Supplied with fitting hardware, this crashbar has been specially developed for the later V7 head design. Engine bars - essential protection for your bike.

Inlet rubber with HT lead guide. This part will only fit the PHM40 carbs with 43.5mm inlet stubs, we recommend measuring your carbs before ordering

Fits between exhaust manifold on cylinder head and carb. Use clip SSA45970

28114360-z 28114360 GU28114360 28 11 43 60
 2811 4360 2811.4360 28.11.43.60

Dimensions:
43.5mm ID x 38mm length

PS 15 rear master cylinder with plastic reservoir

Brembo no. 10.2426.00. Replaces original part with cast reservoir which is no longer available. Also replaces guzzi ref. 29667000. Please note that reservoir is slightly taller than the original, and you may need swap the operating arm from your old master cylinder if this is a different type. This part can be used instead BRC19001 but you will also need to fit a brake reservoir

 10438802 GU10438802 10 43 88 02
 1043 8802 1043.8802 10.43.88.02

Crankcase breather tank / box in black. Also suitable for round barrelled specials where the standard airbox has been replaced with aftermarket filters

3 pipe connections on underside (large, medium and small diameters), plus connection for rocker cover breather pipes. Connects to ENA14157, ENA17700 and ENA95136

14155700-z 14155700 GU14155700 14 15 57 00
 1415 5700 1415.5700 14.15.57.00

Dimensions:
Box measures 110mm x 70mm x 85mm, crankcase spigots measure 8mm OD and 17mm OD respectively

High pressure black fuel line / fuel line

Also known as Guzzi ref. 008239520800, 00823941078, GU00823952080. This high pressure fuel hose is rated to 10 Bar. Also see FUA80000 of a Y shaped connector or FUA80001 for a T shaped fuel line connector. R7 spec. E5 and E10 ethanol resistant

823952080

Dimensions:
7.5mm ID x 13.5mm OD x 1m length

High pressure internal fuel line / submersible fuel line, suitable for immersion in petrol. You will need to cut this to length according to your model

Suitable for modern fuel. 100% ethanol resistant. High pressure fuel hose. This is designed for use submerged in petrol inside the fuel tank. See FUA00004 for pipe clips

Brush holder for Bosch alternator stator

Also known as Guzzi ref. 17712454, 14712452

Includes brushes. See ELA17453

 17712452 GU17712452 17 71 24 52
 1771 2452 1771.2452 17.71.24.52

5 pin mini relay

Also known as Guzzi ref. 30732560 Can be used in place of 4 pin mini relay ELA01561. We recommend keeping a spare one in your tool kit

 01731760 GU01731760 01 73 17 60
 0173 1760 0173.1760 01.73.17.60

Dimensions:
24mm x 15mm x 25mm body

Long screw in polished alloy dipstick with O ring for models with a sump extension but without fairing lowers

28004950-z 28004950 GU28004950 28 00 49 50
 2800 4950 2800.4950 28.00.49.50

Dimensions:
107mm gasket surface to high mark

Black handlebar mounted mirror. Conventional M10 thread, head is threaded for left or right hand fitment.

Supercedes BUMM mirror HAA36021W. See ACA00101 for a black mirror extender kit to extend the reach of this mirror.

Dimensions:
M10 conventional thread, approx. 240mm reach to far edge of mirror, mirror 110mm diameter