Front crank oil seal for models with Bosch or Ducati charging systems

Also known as Guzz ref. 90402839

 90402840 GU90402840 90 40 28 40
 9040 2840 9040.2840 90.40.28.40

Dimensions:
28mm x 38mm x 7mm

Gearbox input seal and output shaft oil seal on big twins, fork seal on Nuovo Falcone. Used as crownwheel shaft oil seal on small twins. Output seal only on 4 speed gearboxes

Supercedes Guzzi ref. 90403547. Used as crownwheel carrier seal on small twins Also known as Guzzi ref. 90403549

 90403548 GU90403548 90 40 35 48
 9040 3548 9040.3548 90.40.35.48

Dimensions:
47mm OD

Replacement alternator brushes or brush kit for Bosch alternators

Also known as Guzzi ref 17712453

14712453-z 14712453 GU14712453 14 71 24 53
 1471 2453 1471.2453 14.71.24.53

Also fits Benelli 900 Sei (Series 2)

Cartridge oil filter UFI 23 149 00

Fits Daytona 1000 models where filter screws into base of sump. This is an 8 sided UFI filter.
Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump.

You may also require SIA10070 which is the crush washer for the drain plug and ENA14036 (sump gasket). Please note that Daytona RS and T5 Polizia use filter SIA15300

 14153000 GU14153000 14 15 30 00
 1415 3000 1415.3000 14.15.30.00

Dimensions:
For 16mm threaded spigot

UFI 30 989 00 flat type air filter, paper filament in rubber surround

See SIA30361 for a reusable K & N air filter

 30113600 GU30113600 30 11 36 00
 3011 3600 3011.3600 30.11.36.00

Dimensions:
220mm x 135mm x 35mm

Output oil seal for drive box

This oil seal fits output side of bevel box

90407085-z 90407085 GU90407085 90 40 70 85
 9040 7085 9040.7085 90.40.70.85

Dimensions:
70mm x 85mm x 8mm

Chrome twin pull Tommaselli 2c twist grip. Includes a pair of handlebar grips, for bikes with dual throttle cables from the bars

As originally fitted to pre 1979 T3's. Not suitable for carbs larger than 36mm (the twistgrip inner will require minor modification to operate PHM40s). This twistgrip can be used on almost any model with suitable custom cables. See ACA14450 for spare rubber. Holes for throttle cable elbow may be smaller than the original and need carefully enlarging with a drill or round file.

 14603450 GU14603450 14 60 34 50
 1460 3450 1460.3450 14.60.34.50

Oil pressure sender

Can also be used in place of oil pressure switch 17768750 and adapter 19055800 on Monza (check which type your small twin uses before replacing). Replaces two part sensor 31999581.

See ENA12640 for replacement crush washer if required

19768720-z 19768720 GU19768720 19 76 87 20
 1976 8720 1976.8720 19.76.87.20

Clutch pushrod seal

 90400616 GU90400616 90 40 06 16
 9040 0616 9040.0616 90.40.06.16

Dimensions:
6mm ID x 16mm OD x 7mm

Clutch cable for pre 1988 models with left hand switchgear integrated into clutch lever clamp

28093060-z 28093060 GU28093060 28 09 30 60
 2809 3060 2809.3060 28.09.30.60

Dimensions:
1265mm outer length, 83mm free length, 9.9mm barrel nipple, 9.9mm barrel nipple