Two California side panel decals

One metre of copper core HT lead, this is superior to the more commonly available carbon core lead

Sold by the metre, one metre is enough for two leads on most models with coils under the fuel tank. For models with coils under the side panel you will need two metres. See ELA14715 and ELA14714 for plug caps and ELA20001 for coil screw cap. See ELA00001 for crimp on HT lead connector

Dimensions:
100cm

Inlet rubber with HT lead guide. This part will only fit the PHM40 carbs with 43.5mm inlet stubs, we recommend measuring your carbs before ordering

Fits between exhaust manifold on cylinder head and carb. Use clip SSA45970

28114360-z 28114360 GU28114360 28 11 43 60
 2811 4360 2811.4360 28.11.43.60

Dimensions:
43.5mm ID x 38mm length

Set of ignition points (made up of two boxes of contacts)

 19709620 GU19709620 19 70 96 20
 1970 9620 1970.9620 19.70.96.20

1 Litre of Millers Classic Pistoneeze SAE20W-50 mineral oil. We recommend this classic engine oil for older (pre 1998) 2 valve twins, it is similar to Castrol GTX 20/50 (which is no longer available). Pistoneeze 20w50 is a moderate detergent premium SAE 20w50 multigrade mineral engine oil. The formulation includes high quality solvent refined base oils with the latest technology performance additives and shear stable viscosity index improver.

Features & Benefits:

• Incorporates modern additive technology with period viscometrics to provide the optimum lubrication characteristics
• Suitable for higher mileage applications where oil consumption is a problem
• Meets up-to-date specifications along with meeting period performance requirements
• Specific gravity at 15C: 0.833
• Kinematic viscosity at 100C: 18.5cSt
• Kinematic viscosity at 40C: 156.8cSt
• Viscosity index: 133

  
  Quantities required:

  • 850/1000 ALL Models, Cali 1100, Quotas - engine: 3l
  • V35, V50, V65, V75 - engine: 2l
  
  
  See ENA41653 for a oil drain kit for your oil change
  
  Please note this oil CANNOT be posted outside of the UK mainland area.
  
   More than 5 in stock

  Also fits Triumph Bonneville T100

  [ CLOSE WINDOW ]
  [ CLOSE WINDOW ]

Rubber tank fastening strap

 19102750 GU19102750 19 10 27 50
 1910 2750 1910.2750 19.10.27.50

Dimensions:
95mm x 40mm x 9mm

Dellorto needle valve kit comprising of valve and felt washer

200 needle valve for VHB24, VHB26 and PHBH carbs

 19934600 GU19934600 19 93 46 00
 1993 4600 1993.4600 19.93.46.00

12 volt ignition coil for models equipped with points, Bosch or Motoplat ignition systems, includes HT lead. Terminal layout is different to original coils- see photos.

Not for Digiplex models. Also known as Guzzi ref. 19716500, 19716520

 31716560 GU31716560 31 71 65 60
 3171 6560 3171.6560 31.71.65.60

Dimensions:
80mm mounting spacing

Cartridge oil filter UFI 23 149 00

Fits Daytona 1000 models where filter screws into base of sump. This is an 8 sided UFI filter.
Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump.

You may also require SIA10070 which is the crush washer for the drain plug and ENA14036 (sump gasket). Please note that Daytona RS and T5 Polizia use filter SIA15300

 14153000 GU14153000 14 15 30 00
 1415 3000 1415.3000 14.15.30.00

Dimensions:
For 16mm threaded spigot

Rebuild kit for Brembo PS 13 handlebar mounted brake and clutch master cylinders, includes all seals, return spring and brake grease. Piston is hollow

This seal kit is for Cali 1100 master cylinders with a hollow pivot pin, does not fit early models with a solid pivot pin. For Cali EV models this only fits master cylinders with a pair of screws in the middle of the cap, it does not fit the later master cylinder which has diagonally opposed screws. Also know as Guzzi ref. 28659378, 000043851, 30659330. NB Included instructions may refer to rear master cylinder applications rather than front. Brembo ref. 110436250

Also fits Cagiva Elefant E750, Ducati 748

Dimensions:
Hollow piston 13mm OD x 38mm