Output oil seal for drive box

This oil seal fits output side of bevel box

 More than 5 in stock

90407085-z 90407085 GU90407085 90 40 70 85
 9040 7085 9040.7085 90.40.70.85

Rotational oil seal for crownwheel carrier in drive box on post 1974 big twins. Front crank oil seal on loop frame models

Also known as Guzzi ref. 90403850 and used on 850 GT and loop frame models for front crank oil seal ( 90403851 )

 More than 5 in stock

 90413850 GU90413850 90 41 38 50
 9041 3850 9041.3850 90.41.38.50

Final drive inner seal

For Breva 750 up to frame no. LL111907

 More than 5 in stock

90407590-z 90407590 GU90407590 90 40 75 90
 9040 7590 9040.7590 90.40.75.90

Rebuild kit for Brembo rear caliper. This is a comprehensive overhaul kit containing dust seals, fluid seals, o ring, bleed nipple, and dust cap

Caliper seal kit

 1 in stock

HIgh performance aluminium velocity stack for airbox to throttle body union. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM

This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA10434

Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.

 1 in stock

Stainless steel exhaust cover for the exhaust link pipe and CAT. Fits easily to the standard exhaust system to improve the styling of the V100. This brushed stainless finish cover also helps shield your feet from the heat of the CAT. Note that this accessory is not compatible with a centre stand.

A quality accessory hand made in Italy for your V100

 1 in stock

Kit of 4 black frame caps to tidy up the bolt heads for the pillion and exhaust footpeg hanger

Simple installation, lasting looks

 2 in stock

The Mistral V-Twin boost is an effective and cost efficient way to cure the fuelling problems common to all modern fuel injected Guzzi's. The V85 TT runs particularly lean and will benefit more than most bikes from the installation of a V-Twin Boost.
Plugging directly into the wiring harness using original connectors, with no cutting or splicing required, installation takes less than ten minutes.

The V-Twin boost features a unique technology to provide your bike with a controlled fuel enrichment.
Make your bike run as it should have done from the factory!

• Quick and easy installation
• Resistant to atmospheric agents and vibrations
• Optimized by Mistral for your bike
• Best response to the opening of the throttle
• Better torque at low-medium range
• Reduction of the on/off effect
• Correct air/fuel ratio in all conditions with real-time modification

 1 in stock

UFI 27 77 900 conical air filter

See FUA90552 for air filter housing O ring

 More than 5 in stock

 17113651 GU17113651 17 11 36 51
 1711 3651 1711.3651 17.11.36.51

Dellorto needle valve kit comprising of valve and felt washer. For PHF36 and PHM40 carbs

Also known as Guzzi ref. 076527649, 14939150 and Ducati ref. 076527645, 0765.27.645

 2 in stock

 14939150 GU14939150 14 93 91 50
 1493 9150 1493.9150 14.93.91.50

Also fits Ducati 750/900 SS Koewe, Ducati 750 F1/Laguna Seca, Ducati 900 MHR, S2, Ducati 900 MHR-I, Ducati 1000 MHR-2,S2