Brembo caliper cover for models with obsolete twin bleed calipers
P9 caliper cover includes cutout each side for bleed nipple. Also known as Guzzi ref. 14654700, 17654760. Please note you may need to trim away the four moulded lugs at the bottom of the cover otherwise these may clash with your pad pins
5 in stock
20325410 GU20325410 20 32 54 10
2032 5410 2032.5410 20.32.54.10
£11.00
INC VAT
£9.17 EX VAT
Single 100cm length of neoprene rubber pipe used for oil breather applications depending on model. Can be used as fuel pipe on carb bikes. Also see FUA00011 as alternative for this pipe
Use hose clip FUA00004
5 in stock
£7.00
INC VAT
£5.83 EX VAT
Combined regulator rectifier to replace separate items on Bosch equipped models. See our wiring instructions page for help installing this reg/rec.
Supplied with long leads for battery and alternator connection. Female spades for alternator and charge sensing, ring connectors for battery. NB this reg/rec should not be used with a lithium-ion battery
1 in stock
£140.00
INC VAT
£116.67 EX VAT
One piece collet for exhaust manifold, one required per cylinder
No longer in production
2 in stock
14121200 GU14121200 14 12 12 00
1412 1200 1412.1200 14.12.12.00
£15.00
INC VAT
£12.50 EX VAT
Stainless steel exhaust stud kit consisting of 4 x studs, 4 x dome head nuts, 4 x wavy washers and 4 x flat washers
On pre-1998 models we recommend combining with a pair of new exhaust polished aluminium flanges - EXA30032
4 in stock
96508040 GU96508040 96 50 80 40
9650 8040 9650.8040 96.50.80.40
£21.00
INC VAT
£17.50 EX VAT
Brakelight switch for handlebar mounted master cylinder
Stop light switch also known as Guzzi ref. 30530526. Please compare with your existing switch to check compatibility. Can be used as a substitute for ELA27815 or ELA30860. Sometimes supplied with three terminals, in this instance disregard middle terminal. Please note that terminals are smaller than standard switch and will need to be soldered on.
3 in stock
30749860 GU30749860 30 74 98 60
3074 9860 3074.9860 30.74.98.60
£13.50
INC VAT
£11.25 EX VAT
Special tool for tightening and untightening the dipstick on small twins. The dipstick can be awkward to undo on these models but this tool makes it simple and quick. No more struggling to grip it or resorting to pliers, just use our tool.
Oil filler tool manufactured from PETG filament these are fully recyclable but as strong as ABS. Dipstick spanner 3D printed in the UK
More than 5 in stock
14927001 GU14927001 14 92 70 01
1492 7001 1492.7001 14.92.70.01
£12.00
INC VAT
£10.00 EX VAT
Rubber brake cable sleeve for lower end of cable
3 in stock
12626300-z 12626300 GU12626300 12 62 63 00
1262 6300 1262.6300 12.62.63.00
£8.30
INC VAT
£6.92 EX VAT
Timing sensor for ignition and tacho
3 pin block connector. Used on models with the smaller 15M ECU
1 in stock
01721600 GU01721600 01 72 16 00
0172 1600 0172.1600 01.72.16.00
£115.00
INC VAT
£95.83 EX VAT
Pair of timing springs for auto advance retard
Distributor springs
1 in stock
19719820 GU19719820 19 71 98 20
1971 9820 1971.9820 19.71.98.20
£10.00
INC VAT
£8.33 EX VAT