Pair of ignition points (made up of Guzzi part numbers 14715429 and 14715430)
More than 5 in stock
14719800 GU14719800 14 71 98 00
1471 9800 1471.9800 14.71.98.00
£29.50
INC VAT
£24.58 EX VAT
Oil pressure sender, M12 thread, male bullet connector
Supercedes Guzzi no. 12768700. Some small twins also require adapter 19055800 (or ELA19720 can be fitted in place of this switch). Check which type your small twin uses before replacing.
See ENA12640 for replacement crush washer if required
More than 5 in stock
17768750 GU17768750 17 76 87 50
1776 8750 1776.8750 17.76.87.50
£10.00
INC VAT
£8.33 EX VAT
Rear crankcase oil seal or rear main oil seal.
Fits Nevada 750 up to engine LT017877 and Nevada 350 to engine PC053625. Also known as Guzzi ref. 90405368. We recommend replacing the rear crank oil seal when replacing the clutch
More than 5 in stock
90405367-z 90405367 GU90405367 90 40 53 67
9040 5367 9040.5367 90.40.53.67
£14.00
INC VAT
£11.67 EX VAT
Cartridge oil filter UFI 23 149 00
Fits Daytona 1000 models where filter screws into base of sump. This is an 8 sided UFI filter.
Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump.
You may also require SIA10070 which is the crush washer for the drain plug and ENA14036 (sump gasket).
Please note that Daytona RS and T5 Polizia use filter SIA15300
More than 5 in stock
14153000 GU14153000 14 15 30 00
1415 3000 1415.3000 14.15.30.00
£10.50
INC VAT
£8.75 EX VAT
UFI 25 46 500 cartridge oil filter. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick
For post 1989 V35, V50 and V65 models use SIA27300 .
NB Packaging may vary. For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer)
More than 5 in stock
19153000 GU19153000 19 15 30 00
1915 3000 1915.3000 19.15.30.00
£8.50
INC VAT
£7.08 EX VAT
UFI 30 989 00 flat type air filter, paper filament in rubber surround
See SIA30361 for a reusable K & N air filter
More than 5 in stock
30113600 GU30113600 30 11 36 00
3011 3600 3011.3600 30.11.36.00
£12.00
INC VAT
£10.00 EX VAT
A4 marine grade stainless steel M6 bleed nipple for Brembo F05 and twin bleed P2 F08 & F09 calipers. Manufactured specially for Gutsibits as a replica of the original Brembo M6 bleed nipple
Use M10 bleed screw SSA36794 for single bleed (later) P8 calipers. Ducati ref. 079539787
See BRA36794 for rubber cap
More than 5 in stock
Also fits Benelli 250 TS, Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 F1/Laguna Sec, KTM 250XC, KTM 250SX, KTM 250EXC,
£8.00
INC VAT
£6.67 EX VAT
Brembo kit containing replacement seal and angled elbow for connecting remote brake fluid reservoir to PS 15, PS 11 and PS 13 rear master cylinders
Also known as Brembo ref. 110312720
2 in stock
19659500 GU19659500 19 65 95 00
1965 9500 1965.9500 19.65.95.00
£7.50
INC VAT
£6.25 EX VAT
Clutch thrust bearing complete, sits in recess in rear gearbox casing.
This bearing is the higher quality OE bearing used on recent models
3 in stock
2A000376
£21.00
INC VAT
£17.50 EX VAT
One metre of copper core HT lead, this is superior to the more commonly available carbon core lead
Sold by the metre, one metre is enough for two leads on most models with coils under the fuel tank. For models with coils under the side panel you will need two metres. See ELA14715 and ELA14714 for plug caps and ELA20001 for coil screw cap. See ELA00001 for crimp on HT lead connector
More than 5 in stock
£7.00
INC VAT
£5.83 EX VAT