Oil pressure sender, M12 thread, male bullet connector

Supercedes Guzzi no. 12768700. Some small twins also require adapter 19055800 (or ELA19720 can be fitted in place of this switch). Check which type your small twin uses before replacing.

See ENA12640 for replacement crush washer if required

 More than 5 in stock

 17768750 GU17768750 17 76 87 50
 1776 8750 1776.8750 17.76.87.50

Rear crankcase oil seal or rear main oil seal.

Fits Nevada 750 up to engine LT017877 and Nevada 350 to engine PC053625. Also known as Guzzi ref. 90405368. We recommend replacing the rear crank oil seal when replacing the clutch

 More than 5 in stock

90405367-z 90405367 GU90405367 90 40 53 67
 9040 5367 9040.5367 90.40.53.67

Cartridge oil filter UFI 23 149 00

Fits Daytona 1000 models where filter screws into base of sump. This is an 8 sided UFI filter.
Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump.

You may also require SIA10070 which is the crush washer for the drain plug and ENA14036 (sump gasket). Please note that Daytona RS and T5 Polizia use filter SIA15300

 More than 5 in stock

 14153000 GU14153000 14 15 30 00
 1415 3000 1415.3000 14.15.30.00

UFI 25 46 500 cartridge oil filter. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick

For post 1989 V35, V50 and V65 models use SIA27300 .
NB Packaging may vary. For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer)

 More than 5 in stock

 19153000 GU19153000 19 15 30 00
 1915 3000 1915.3000 19.15.30.00

UFI 30 989 00 flat type air filter, paper filament in rubber surround

See SIA30361 for a reusable K & N air filter

 More than 5 in stock

 30113600 GU30113600 30 11 36 00
 3011 3600 3011.3600 30.11.36.00

UFI 30 814 00 flat type air filter, paper filament in rubber surround

NB Packaging may vary

 More than 5 in stock

 28113650 GU28113650 28 11 36 50
 2811 3650 2811.3650 28.11.36.50

A4 marine grade stainless steel M6 bleed nipple for Brembo F05 and twin bleed P2 F08 & F09 calipers. Manufactured specially for Gutsibits as a replica of the original Brembo M6 bleed nipple

Use M10 bleed screw SSA36794 for single bleed (later) P8 calipers. Ducati ref. 079539787

See BRA36794 for rubber cap

 More than 5 in stock

Also fits Benelli 250 TS, Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 F1/Laguna Sec, KTM 250XC, KTM 250SX, KTM 250EXC,

Red lens for oblong rear light, includes clear section to illuminate number plate

Can be used to replace tail light lens on Lario and Le Mans 1000, note that this one does not have side 'wings' but is functional on these models

 1 in stock

 65741700 GU65741700 65 74 17 00
 6574 1700 6574.1700 65.74.17.00

Clutch thrust bearing complete, sits in recess in rear gearbox casing.

This bearing is the higher quality OE bearing used on recent models

 3 in stock

2A000376

One metre of copper core HT lead, this is superior to the more commonly available carbon core lead

Sold by the metre, one metre is enough for two leads on most models with coils under the fuel tank. For models with coils under the side panel you will need two metres. See ELA14715 and ELA14714 for plug caps and ELA20001 for coil screw cap. See ELA00001 for crimp on HT lead connector

 More than 5 in stock